Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Burbank, CA
Gate access control in Burbank runs into the same heat and the same aged iron work everywhere else in the San Fernando Valley does, with one local twist: a lot of the systems we open up were installed by studio contractors, so the hardware is commercial-grade and the wiring is rarely documented. A failed keypad on a hillside home near the Verdugo foothills is usually a heat-related solder joint or a sun-baked keypad face, not a bad board. Call (213) 674-2473 and we’ll name the problem and the price before anything gets touched.
Why Burbank Homes Are Different
Burbank’s residential streets are dominated by 1940s and 1950s post-war ranch homes and Craftsman bungalows, and a remarkable number still hang original ornamental wrought-iron swing gates on concrete or brick posts that have heaved and shifted for sixty-plus years. When the post leans, the gate leans with it, and the hinges, the latch, and the access-control hardware all carry load they were never designed for. The alley-access lots in older Burbank tracts add a second entry point, so rear driveway gates need their own keypads, their own safety loops, and their own service calls.
Heat is the other constant. Burbank sits deep in the Valley heat basin where summer days routinely reach 100 to 110 degrees, far hotter than coastal Los Angeles neighborhoods. Paint and powder-coat on iron gates breaks down faster here, wood gate boards warp, and automated gate motor units run hot enough that manufacturer duty-cycle specs stop matching reality. Santa Ana wind events add cyclical stress on hinges and openers every fall.
Our Main Burbank Services
Two calls dominate Burbank gate service: repairs to existing gates that have stopped swinging or sliding true, and full installations where an older property is getting its first automated gate. The three services below cover the full scope of what we do across the city.
Gate Repair in Burbank
Most Burbank gate repairs trace back to one of three causes: a post that has shifted out of plumb, a hinge or roller that has worn to the point of binding, or an access-control component that has failed from heat and age. We measure the gate before we unbolt anything, so the fix restores travel the way the hardware was designed to move. Every repair leaves with a written record of what was changed and a photo log of the finished work. See Gate Repair in Burbank for the full breakdown.
Gate Installation in Burbank
New gate installations in Burbank have to work around the existing post conditions, and on the older ranch lots that often means core-drilling into brick or pouring new steel-reinforced posts before the gate ever goes on. We quote the post work, the gate, the opener, and the access control as one written price. No separate surprises from a subcontractor. The full process is on the Gate Installation in Burbank page.
Gate Motor & Opener in Burbank
Burbank’s heat shortens motor life, and a lot of the homes here run openers that were sized for coastal conditions, not Valley summers. We stock motors and control boards for nine major automation brands, so the conversation starts with repair and only moves to replacement when the motor is genuinely beyond service. Brand coverage, rebuild options, and the written-price process are detailed on Gate Motor & Opener in Burbank.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Burbank
Gate access control in Burbank means keypads, phone entry, card readers, video intercoms, and remote controls wired into automated gates. The local challenge is twofold: heat ages keypad membranes and solder joints faster than manufacturers anticipate, and the studio-adjacent streets and Verdugo foothill homes often run proprietary access-control hardware tied to security networks, so parts sourcing and programming knowledge actually matter here. Our Gate Access Control service covers the hardware, the wiring, and the programming on every major system.
Keypad Entry
Signs you need it
The keypad takes multiple presses to register digits, works intermittently in heat, or the front membrane is cracked and faded.
What it costs in Burbank
Replacement keypad entry systems in Burbank typically run $150-$600 depending on whether we’re replacing the keypad face, the controller behind it, or the entire wired assembly.
How we do it
We test the existing controller before swapping parts, then replace only what has failed and photograph the new wiring and programming settings.
Phone Entry
Signs you need it
Calls fail to ring through to your phone, the gate opens for some callers but not others, or you hear static instead of a dial tone at the call box.
What it costs in Burbank
Phone entry systems in Burbank run $400-$1,600 depending on whether we’re repairing the existing unit, re-wiring the connection, or installing a new cellular-capable module.
How we do it
We trace the phone line or cellular pathway first, identify whether the failure is in the call box, the relay, or the carrier signal, and then write the fix and the cost before ordering any parts.
Video Intercom
Signs you need it
The video feed is frozen, night vision doesn’t activate, or the indoor monitor has lost sync with the outdoor camera unit.
What it costs in Burbank
Video intercom repair in Burbank typically runs $200-$750, with full replacement systems running higher depending on camera resolution and monitor count.
How we do it
We check power to the outdoor unit, test signal continuity on the video pair, and replace cameras, monitors, or cable runs based on what the meter shows.
What Gate Access Control Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Keypad entry repair or replacement | $150-$600 |
| Phone entry system repair | $400-$1,600 |
| Video intercom repair | $200-$750 |
Can you program my existing studio-installed access control hardware?
In most cases, yes. We regularly work on proprietary access-control hardware on Burbank studio lots and hillside homes. We verify manufacturer protocol compatibility before quoting, and we document every programming change in writing.
Is a wired keypad better than a wireless one in Burbank heat?
Wired keypads hold up better in sustained Valley heat because they don’t rely on battery chemistry or radio modules that can drift at high temperatures. We’ll recommend wired unless your post layout makes it impractical. Call (213) 674-2473 for a written quote.
Gate Parts & Welding in Burbank
Gate parts and welding in Burbank usually means one of two things: the original wrought-iron hardware has outlasted its hinges and posts, or the gate itself needs a structural repair that no off-the-shelf part will fix. Valley heat accelerates finish failure, and the heaved concrete posts on older ranch lots mean we’re often welding reinforcement plates or re-hanging gates on new threaded anchors. Our Gate Parts & Welding service covers the metal work and the component replacement in one call.
Hinge Replacement
Signs you need it
The gate sags on the latch side, scrapes the ground, or the hinge pin has worn into an oval.
What it costs in Burbank
Hinge replacement in Burbank runs $120-$450 per hinge depending on gate weight, material, and whether we’re replacing the leaf, the pin, or both.
How we do it
We support the gate, measure the existing hinge centers, and weld or bolt the new assembly in place, then re-check the swing for full travel without binding.
Post Replacement
Signs you need it
The post leans visibly, the gate gap has widened at the top, or the post base is cracked and spalling from rust inside the concrete.
What it costs in Burbank
Post replacement in Burbank typically runs $400-$1,200 per post depending on depth, concrete work, and whether the old post can be cut rather than demoed.
How we do it
We cut or pull the old post, set the new one in concrete at full depth, and only re-hang the gate after the post has been checked for plumb and level.
Custom Welding
Signs you need it
The wrought iron has cracked clean through, a decorative scroll has snapped off, or the gate frame needs reinforcement after years of sag repair.
What it costs in Burbank
Custom welding in Burbank runs $150-$800 depending on the extent of the repair, the material thickness, and whether finish work is needed after the weld.
How we do it
We clean the joint back to bare metal, weld the repair, grind it smooth, and apply a primer coat that matches the surrounding finish.
What Gate Parts & Welding Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Hinge replacement | $120-$450 per hinge |
| Post replacement | $400-$1,200 per post |
| Custom welding | $150-$800 |
Do you weld wrought iron on site in Burbank?
Yes, we weld on site for most repairs. If the repair requires a bench setup or controlled heating, we’ll take the gate section to our shop and return it installed with the same written price. Call (213) 674-2473 to schedule a look.
Can you match the original ironwork on a 1950s Burbank gate?
We can match the profile and general appearance of most original Burbank wrought-iron work, including scrolls and picket spacing. We’ll show you a photo of the fabricated piece before it’s installed. Estimates are free.
Brands We Service in Burbank
We service Viking, Ghost Controls, DoorKing, and Elite equipment, along with five other major automation brands. We keep common control boards, remotes, and photo-eyes in local stock, so many Burbank repairs don’t wait on a parts order. See our brands for the full equipment list.
Pricing for Gate Repair in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Tune-up, travel adjustment, photo-eye alignment | $95-$190 |
| Circuit board replacement | $250-$550 |
| Remote control or receiver replacement | $85-$250 |
| Safety sensor replacement | $140-$330 |
| Hinge replacement | $120-$450 per hinge |
| Post replacement | $400-$1,200 per post |
| Custom welding | $150-$800 |
| Keypad entry repair or replacement | $150-$600 |
| Phone entry system repair | $400-$1,600 |
| Video intercom repair | $200-$750 |
Burbank pricing runs higher than coastal neighborhoods when post work or heat-related board failures are involved, because the concrete is older and the components have been baking in Valley summers. Every price on this page is a written range, and the exact figure is agreed upon in writing before any work starts.
Neighborhoods We Serve in Burbank
We work across Burbank, from the hillside streets near the Verdugo foothills down through the flat ranch tracts. A quick sample:
- Rancho Adjacent
- Magnolia Park
- Toluca Woods
- Burbank Hills
- North Hollywood-adjacent Burbank
Most Burbank calls get a technician dispatched the same day, and we coordinate scheduling around studio gate access hours when needed.
Service Area - Cities Near Burbank
Our Burbank crews also cover the surrounding Valley and Eastside neighborhoods. You’ll find the same written-price process in North Hollywood, CA, Studio City, CA, Van Nuys, CA, and West Hollywood, CA.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Burbank
Most Burbank calls get a same-day dispatch, especially for gates stuck open or stuck closed. A live person answers the phone 24/7 at (213) 674-2473, and we’ll give you a written price before work begins.
Most gate repairs and access-control replacements on existing gates don’t require a Burbank permit. Full gate installations or new post footings may. We’ll tell you if a permit applies to your job before we schedule it.
Leave the gate in whatever position it’s stuck in, and don’t force it. Forced travel on a binding gate can bend hinge points beyond simple replacement. We’ll arrive, assess, and put the fix in writing first.
Call (213) 674-2473 for a free estimate on any gate repair, access control, or parts and welding work in Burbank. You’ll get a written scope, a written price, and a photo record when the job is done.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burbank Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.