Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Burbank
A gate motor replacement in Burbank typically costs $380 to $1,340 for parts and labor, while circuit board repair runs $210 to $460. Our Gate Motor & Opener team reaches most Burbank streets in under an hour, because dispatch is coordinated from our Los Angeles office and crews are stationed across the San Fernando Valley. We carry Linear, Viking, Ghost Controls, and DoorKing parts in the truck, and we hand you a written price before any tool comes out. Call (213) 674-2473 if your opener died this morning.
Why Vance Gate Repair Los Angeles Is Burbank’s Preferred Gate Motor & Opener Company
We repair and replace gate operators across Burbank every week, from Magnolia Park bungalows to the gated hillside properties near the Verdugo foothills. The job is different here than in Van Nuys or North Hollywood. Burbank has a density of automated gates tied to studio lots and entertainment-industry homes that you simply don’t see two miles west, and that concentration shapes the work. Our techs know which properties near Warner Bros. and Walt Disney Studios use commercial-grade slide operators, which neighborhoods still run original 1960s swing gates on heaving posts, and which openers burn out first when the Valley heat settles in.
Adrian Vance started this company in 2014 after years of access-control work on commercial sites, and that background is why our documentation looks like an inspection report rather than a sticky note. Every job leaves a photo record: what we found, what we adjusted, what part number went in. Under Haven Standard Clause 4, you get that photo log before we leave, and Clause 1 means the written price is in your hand before work starts. No verbal estimate, no invoice surprise at the end. Call (213) 674-2473 and you’ll speak to a live person, at any hour.
Our Gate Motor & Opener Services in Burbank
Motor Installation
Most Gate Installation - Burbank projects for swing-gate motors run $720 to $1,340 depending on brand, gate weight, and whether the existing arm bracket is reusable. We install LiftMaster, FAAC, BFT, and the other brands we service without steering you toward a brand we happen to prefer. In Burbank’s 1940s ranch neighborhoods, the bigger variable is often the post: if the brick or concrete has heaved, a new motor on a crooked post fails early, so we address alignment before mounting anything.
Motor Repair
Not every dead opener needs replacement. In Burbank, we frequently repair operators where the limit switch drifted, a capacitor failed, or the control board cooked from repeated thermal cycling. A board replacement runs $210 to $460, and we photograph the new wiring and settings before we close the housing. On a hillside street near Warner Bros., we’ve repaired units that other companies said needed full replacement, because the failure was a $90 relay, not the motor. We show you the evidence.
Linear Motor Service
Linear is common on Burbank’s alley-access lots, where rear driveway gates get as much use as the front. We stock Linear control boards, remote receivers, and limit-switch kits so most repairs are one visit. A Linear motor swap in Burbank typically runs $460 to $850. If your Linear opener is clicking but not moving, call us before you order parts online, because half the time the issue is the capacitor or a misaligned photo-eye, not the motor itself.
Slide Motor Service
Burbank’s studio-adjacent properties and hillside homes often run heavy commercial-grade slide gates, and slide operators work hard in this climate. A slide motor replacement in Burbank typically runs $680 to $1,240 depending on gate length and whether the rack and pinion needs replacement. We also service rack drives that have started skipping teeth under thermal load. Santa Ana winds twist lightweight aluminum slide gates just enough to cause gear wear, so after a motor replacement we check the rack alignment and limit travel so the new motor isn’t fighting the gate.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Burbank
We service nine automation brands without pushing you toward one, which matters when a Viking slide operator sits on a Warner Bros.-adjacent property and a Ghost Controls unit guards a Rancho District driveway. We keep stock parts in the truck for Linear, Viking, Ghost Controls, and DoorKing, because those are the most common operators on Burbank gates. If we don’t have the part on hand, we can usually have it by the next morning and are back within a day. You get a written record of the brand, model, and part number installed, so the next technician doesn’t waste your money rediscovering what we already found.
Common Gate Motor & Opener Problems We See in Burbank Homes
- Summer thermal shutdowns. Burbank’s 100-110°F summer days push gate operators past duty-cycle limits faster than coastal LA. Boards and motors trip thermal overloads, then work fine after dark. We replace degraded components and adjust force settings so the opener doesn’t keep shutting down during a heat wave.
- Santa Ana wind strain. Wind events off the Verdugo hills buffet lightweight aluminum slide gates, which twists them just enough to stress rack-and-pinion drives. We see worn gear teeth and loose rack bolts on exposed hillside gates, especially on studio-adjacent streets.
- Heaved hinge posts on older homes. Burbank’s 1940s-1960s tracts sit on expansive clay soil. As it swells and shrinks, brick and concrete posts shift, pulling swing gates out of level. The opener then strains against misalignment until the motor burns out. Leveling the gate before adjusting the opener is the real fix.
- Photo-eye misalignment from alley traffic. Rear gates on Burbank’s alley-access lots take bumps from trash bins and delivery vehicles. A photo-eye knocked two inches out of line will stop the gate mid-cycle or refuse to close. We re-align, re-test, and photograph the final position.
Pricing for Gate Motor & Opener in Burbank, CA
Here are the dollar ranges we write on estimates for Burbank work: motor replacement, $380 to $1,340; control board repair, $210 to $460; photo-eye realignment, $65 to $120; intercom-to-opener integration, $180 to $420; battery backup installation, $220 to $480. What moves the number is gate type (slide vs swing), gate weight, and whether the existing arm bracket, rack, or hinge posts are still sound. We quote the price in writing before any work starts, per Haven Standard Clause 1. If you have another company’s written estimate, bring it to us: we’ll give you a free second opinion and match the same scope line for line. Call (213) 674-2473 for a free estimate.
We Also Serve Cities Near Burbank
While this page focuses on Gate Motor & Opener in Burbank, we dispatch the same teams to North Hollywood, Studio City, Van Nuys, and West Hollywood. Call (213) 674-2473 and we’ll route the nearest available technician to your gate, wherever you are in the Valley.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Burbank
Thermal overload, in most cases. Burbank’s summer highs of 100-110°F heat the operator housing far beyond what the motor’s duty-cycle rating accounts for, and the unit shuts itself down to avoid burning out. The fix is usually a cooling inspection: we clear vent screens, check the capacitor, and sometimes reposition the operator out of direct afternoon sun. We also adjust the force settings for the hotter operating range. Call (213) 674-2473 if your opener died in the heat, and we’ll diagnose it on site.
Yes. This is Burbank-specific work we’ve done on multiple studio-adjacent properties. We can wire an opener to accept an existing access card or intercom release, pair it with a keypad, or add a battery backup so the gate still opens during a power outage. We test everything with the actual card or fob you use, not just a meter. Bring us your access-control documentation and we’ll review it before quoting.
The real fix is getting the gate level and the hinge posts stable before the opener does more work. In Burbank, clay soil under 1940s-1960s homes causes posts to heave gradually, and a sagging gate adds enough load to burn out a motor within a year or two. We address the alignment first, and only then service or replace the opener. Our photo log documents the before, during, and after, so you see exactly what was corrected.
Yes, in two ways. Burbank enforces safety standards for photo-eyes and reverse mechanisms on automated gates, so any repair we do must keep those safety edges and optical sensors functional. We don’t bypass them, and we don’t wire around a failing sensor to get a gate moving. Second, hillside and studio-adjacent properties sometimes have fire-access or security stipulations written into their permits. We’ll note any non-compliant findings in our written report.
Alley gates on older Burbank tracts often get daily use from trash collection, service vehicles, and rear driveway traffic, and their track accumulates sand and grit that adds rolling resistance. Combined with summer heat, a slide operator that isn’t maintained burns out faster than a front-gate unit. When we replace a slide motor, we clean the track, adjust the rack, and photograph the finished setup. Call (213) 674-2473 if your alley gate stopped moving.
Call Vance Gate Repair Los Angeles for Gate Motor & Opener in Burbank
If your gate opener is down, or you’re planning a replacement before the heat returns, call us at (213) 674-2473. We’ll give you a written price before we start, show up with parts for your brand, and leave a photo record of the work. Free estimates, a live answer at any hour, and a 365-day promise that stands behind every repair. That’s the standard we work to on every Burbank gate we touch.
Written by Adrian Vance, Owner at Vance Gate Repair Los Angeles, serving Burbank and the San Fernando Valley since 2014.