Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Beverly Hills, CA
Gate access control in Beverly Hills usually means one thing before any wiring gets touched: a house in the hills with a steep driveway, a legacy telephone-entry panel, and a gate motor that was installed with a permit the city of Beverly Hills actually enforces. We handle the access side first because that’s what fails first when Santa Ana wind gusts push a gate off its limit and the keypad stops talking to the operator. Call (213) 674-2473 and you’ll get a written price before anyone picks up a tool.
Why Beverly Hills Homes Are Different
North of Sunset, the lots climb. Driveways angle up at grades that make swing gate operators work against gravity on every cycle, so limit switches drift and motors burn out faster than they would on flat ground. The housing stock runs from 1920s Spanish Colonials to recent mega-mansions, and the older masonry pillars that hold gate hinges crack and shift as hillside soil moves through rainy winters. South of Sunset the grading is gentler, but the original 1920s-1940s pillars show the same problem: post-settlement that pulls leaves out of alignment and leaves a gate dragging on its striker. Beverly Hills Building & Safety requires permits for gate motor replacements and structural modifications, separate from LA County, which means some job quotes here include a compliance step that other cities skip. And because the estate gate concentration per square mile is among the highest in the country, the operators we see are disproportionately high-end European units: FAAC, BFT, Viking Access, often paired with custom ornamental ironwork that demands a welder, not just a parts swap.
Our Main Beverly Hills Services
Most calls to our Beverly Hills line start with one of three problems: a gate that won’t open, a gate that needs to replace an old one, or a motor that’s given up. Each has its own page so you can read the details before calling.
Gate Repair in Beverly Hills
When a gate stops mid-travel, slams past its stop, or groans on every cycle, the fix is usually mechanical first: a worn roller, a bent hinge, a limit switch that needs resetting. In Beverly Hills we photograph what we find, reset what can be reset, and replace what cannot, then leave you a written record of every part and adjustment. Gate Repair in Beverly Hills
Gate Installation in Beverly Hills
A new gate in Beverly Hills means matching the existing architectural language: Spanish Colonial, Mediterranean, or modern glass and steel. We measure the opening, check the pillar condition, and quote a written price that includes the gate, the operator, and the permit coordination the city requires before structural work begins. Gate Installation in Beverly Hills
Gate Motor & Opener in Beverly Hills
When a gate opens fine by hand but will not move on its own, the operator is the prime suspect. We service nine automation brands, so we can usually repair the motor already on the property instead of pushing a replacement, then reset and photograph the limit-switch positions. Gate Motor & Opener in Beverly Hills
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Beverly Hills
Beverly Hills access-control jobs nearly always involve a tech stack older than the house’s last remodel: a telephone-entry intercom wired by one contractor, a video intercom added by another, and a gate operator that predates both. The trick is making the keypad, phone system, and operator talk to each other without voiding the low-voltage warranty on any of the newer pieces, which is why we treat Gate Access Control as its own discipline rather than an add-on. In the hills, access panels bake in direct sun and salt air from the marine layer accelerates corrosion on external keypads and card readers faster than neighborhoods farther inland.
Keypad Entry
Signs you need it
Codes stop working, some buttons fail while others work, or the keypad lights up but will not release the gate.
What it costs in Beverly Hills
Keypad replacement in Beverly Hills typically runs $285-$695 depending on whether it’s a standalone numeric pad or a flush-mount commercial unit tied to a legacy intercom.
How we do it
We test voltage at the keypad and the operator terminal, replace or rewire the unit, then reprogram codes and photograph the finished wiring.
Video Intercom
Signs you need it
The camera shows a black screen, call audio is one-way, or the unit rings but the door release button does not trip the gate.
What it costs in Beverly Hills
Video intercom repair in Beverly Hills runs $460-$1,300 when the existing unit is serviceable; full replacement with a newer IP system usually lands between $1,800 and $3,400.
How we do it
We trace the low-voltage path from the station to the operator, verify the relay is actually closing, and either repair the existing hardware or wire a compatible new unit in its place.
What Gate Access Control Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Keypad replacement | $285-$695 |
| Video intercom repair | $460-$1,300 |
| Full video intercom replacement | $1,800-$3,400 |
Can you work with the intercom system already on my gate instead of replacing it?
Yes. We test the existing wiring and panel first, then repair what’s serviceable. Replacement only comes into the conversation when the unit itself has failed beyond the cost of new hardware.
Will a new keypad work with a phone-entry system installed by another contractor?
Almost always yes, if the relay wiring is intact. We verify compatibility on site and document the connection so the original contractor’s low-voltage warranty stays valid. Call (213) 674-2473 and we’ll quote it in writing before starting.
Gate Parts & Welding in Beverly Hills
Most Beverly Hills gate failures we see are mechanical before they’re electrical: a hinge pin worn oval, a post that’s drifted out of plumb, a rail that’s bent from years of Santa Ana debris strikes. The flatlands south of Sunset have 1920s-1940s pillars that crack and settle, and the hillside estates north of Sunset throw a second variable at us: operators working on severe grades that accelerate wear on every moving part. Gate Parts & Welding covers the physical side of the gate, and in Beverly Hills that often means fixing what’s there rather than replacing a whole leaf.
Hinge Replacement
Signs you need it
The gate sags, scrapes the ground on the latch side, or the top hinge shows a visible gap while the bottom one is compressed.
What it costs in Beverly Hills
Hinge replacement in Beverly Hills typically runs $180-$520 per pair depending on whether it’s a standard weld-on barrel hinge or a custom ornamental strap hinge.
How we do it
We lift and secure the leaf, cut or unbolt the failed hinge, weld or bolt the new one in, then set the gate back and photograph the alignment.
Post Replacement
Signs you need it
The post leans, the gate no longer latches cleanly, or fresh cracks appear in the masonry where the hinge plate is anchored.
What it costs in Beverly Hills
Post replacement in Beverly Hills runs $900-$2,800 depending on depth, whether the old post is embedded in masonry or concrete, and whether the existing gate leaf can be reused.
How we do it
We pull the old post, set the new one at proper depth in fresh concrete, verify plumb in both directions, then rehang the gate and photograph the finished set.
What Gate Parts & Welding Costs in Beverly Hills
| Item | Typical range in Beverly Hills |
|---|---|
| Hinge replacement | $180-$520 per pair |
| Post replacement | $900-$2,800 |
| Rail repair | $240-$690 |
Can you weld a custom gate section to match an ornamental design that’s 70 years old?
Yes. We match the existing profile and finish as closely as the material allows, and we show you a photo record of the work before the leaf is rehung. Call (213) 674-2473 and we’ll write the scope and price first.
My gate posts are original to the house. Can you keep them and just repair the structure?
Often, yes. If the post is stable and only the hinge plate or anchor has failed, we repair in place rather than replacing the post. We’ll tell you on site which route is actually necessary before any work begins.
Brands We Service in Beverly Hills
We work on Linear, Viking, Ghost Controls, and DoorKing operators, among others. Keeping common parts on the truck means many Beverly Hills jobs are one visit. See the full list on our brands page.
Pricing for Gate Repair in Beverly Hills, CA
| Service | Typical range in Beverly Hills |
|---|---|
| Gate repair service call | $95-$145 |
| Gate motor replacement | $650-$2,400 |
| Keypad replacement | $285-$695 |
| Video intercom repair | $460-$1,300 |
| Hinge replacement | $180-$520 per pair |
| Post replacement | $900-$2,800 |
| Rail repair | $240-$690 |
| Gate roller replacement | $180-$420 |
Prices in Beverly Hills run higher than in flat neighborhoods because hillside grades shorten operator life, older masonry pillars require more labor to reset correctly, and custom ornamental work demands matched welding rather than off-the-shelf parts. Whatever the job, the price is written and agreed before any work starts, so the invoice matches the quote.
Neighborhoods We Serve in Beverly Hills
We run calls throughout Beverly Hills, including:
- Trousdale Estates
- Beverly Hills Flats
- Beverly Glen
- Coldwater Canyon
- Beverly Park
Response time across Beverly Hills is typically same-day or next-morning for emergency gate failures, with the hills properties adding a little drive time depending on where the canyon road is at that hour.
Service Area - Cities Near Beverly Hills
When Beverly Hills jobs take us to the edge of the service area, we also cover West Hollywood, CA, Studio City, CA, Culver City, CA, and Sherman Oaks, CA. Each city has its own permit quirks and housing stock, but the same written-price rule applies everywhere we go.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Beverly Hills
Most Beverly Hills emergency calls get a same-day visit; hillside locations off Coldwater or Beverly Glen may push into the following morning depending on call volume. A live person answers at (213) 674-2473 around the clock, so you’ll know the schedule the moment you call.
Motor replacements and structural modifications in Beverly Hills require city permits, separate from LA County. We handle the coordination as part of the written scope, so the permit step is accounted for in the price before work starts.
Yes. Every visit leaves a photo record of what was found, what was adjusted, and what was replaced, along with a written list of any part numbers installed. You keep the record, and we file it for future service calls.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Beverly Hills Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.