Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Culver City, CA
Gate access control in Culver City means something different than it does ten miles inland. The salt-heavy marine layer off Marina del Rey settles over iron gate frames, hinge welds, and circuit boards every night, and the city’s stock of 1920s-1940s Spanish Colonial homes still carries original wrought iron that’s been corroding for eighty-plus years. We service everything from residential keypad systems on renovated bungalows in Mar Vista to card-reader slide gates on the studio lots along Washington and Jefferson Blvds. Call us at (213) 674-2473 and you’ll get a written price before anyone picks up a tool.
Why Culver City Homes Are Different
Culver City sits three to four miles from the coastline, which puts the entire residential grid inside the marine layer’s nightly reach. That salt-laden moisture is the single biggest reason gate components fail earlier here than in the Valley or the eastern basin. Hinge welds oxidize from the inside out, circuit boards corrode at the terminals, and slide-gate rails pit faster than the manufacturer’s lifespan tables would predict. Technicians who only work inland underestimate this. We don’t, because we see it every week in Fox Hills, Ladera Heights, and the older residential blocks off Culver Boulevard.
The housing stock compounds the problem. Culver City’s older core is dominated by Spanish Colonial and Mediterranean Revival homes built between 1920 and 1945, many with original or early-replacement wrought iron driveway gates. That iron is thick, ornate, and often beautiful. It’s also decades past its service life, with rust creeping through the bottom rails and hinge posts that have settled out of square. Fox Hills adds 1970s-era condominium complexes with slide-gate operators and keypads well past their rated service window. Then there’s the permit layer: Culver City runs its own Community Development department, separate from LADBS, and gate work on many properties requires city approval even when the property across the street falls under unincorporated LA. We know which jobs trigger a permit pull and which don’t.
Our Main Culver City Services
Most Culver City homeowners call us for one of three reasons: a gate that won’t open, a gate they need built, or a motor that’s given up. Each service has its own page with full pricing detail.
Gate Repair in Culver City
A sagging wrought iron gate in Culver City usually means the hinge welds have fatigued or the post has shifted in the clay-heavy soil. Gate Repair in Culver City covers hinge and post work, rail straightening, dent and crack repair, and full restoration of drive and pedestrian gates. We match the original ironwork where we can, including the Mid-Century detailing on Village Green properties, and every repair gets a written price and photo documentation before we leave.
Gate Installation in Culver City
New driveway gates in Culver City have to clear two hurdles: the city’s own permitting process and the aesthetic expectations of the neighborhood. Gate Installation in Culver City covers custom steel and aluminum gates, slide and swing configurations, and pedestrian gates matched to the home’s architecture. We quote a firm written price after measuring on site, and we photograph the install from footing to final swing.
Gate Motor & Opener in Culver City
Coastal moisture kills gate operators faster than almost anything else, and Culver City’s marine layer does not discriminate between a LiftMaster on a Fox Hills condo slide gate and a Viking on a Mar Vista swing gate. Gate Motor & Opener in Culver City covers replacement and repair across nine brands, with same-visit diagnosis and a written quote on the replacement cost before work starts.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Culver City
Access control in Culver City usually means one of two calls: a keypad or intercom system on a residential driveway that’s stopped releasing the gate, or a commercial-grade card reader on an office or studio lot that’s intermittently failing. The coastal moisture that eats iron also corrodes the low-voltage terminals and relay contacts inside keypads, card readers, and telephone entry units. That’s why we treat access control as a full Gate Access Control diagnostic, not a part swap: we trace the low-voltage circuit, identify where the corrosion or failed relay is, and document the repair with photos and a written record of the part number installed.
Keypad Entry
Signs you need it
Buttons that need multiple presses, a keypad that works intermittently after rain, or codes that suddenly delete themselves.
What it costs in Culver City
Replacement keypad units and weatherproof enclosures typically run between $125 and $210 installed.
How we do it
We test the keypad’s output at the control board, replace the unit if the contacts are corroded, reprogram your codes, and photograph the new installation.
Remote Control
Signs you need it
Remotes that only work from ten feet away, stop pairing after a battery change, or open the gate but won’t close it.
What it costs in Culver City
Remote programming and replacement typically runs from $75 to $165 per remote for most brands.
How we do it
We identify the receiver frequency and age, swap in a compatible remote if the old one’s failed, and test range from inside your car where you actually use it.
Phone Entry
Signs you need it
A dial-to-open system that rings a disconnected number, won’t bridge calls to your cell, or drops the gate release signal.
What it costs in Culver City
Phone entry unit replacement and programming typically lands between $460 and $975 depending on whether we reuse the existing housing.
How we do it
We open the unit, test the telephone line voltage and relay, replace the board if it’s dead, reprogram your forwarding numbers, and test the full call-release cycle.
Card Reader
Signs you need it
Cards that work sometimes but not others, a reader that beeps without releasing the gate, or no response at all.
What it costs in Culver City
Card reader replacement with new credentials usually runs $650 to $1,100 installed on a single gate.
How we do it
We check the reader’s power and data lines at the controller, replace the reader or the cable run as needed, issue new credentials, and leave you a written list of what was installed.
What Gate Access Control Costs in Culver City
| Item | Typical range in Culver City |
|---|---|
| Keypad replacement and programming | $125 - $210 |
| Remote programming and replacement | $75 - $165 per remote |
| Phone entry unit replacement | $460 - $975 |
| Card reader replacement with credentials | $650 - $1,100 |
Do you handle access control on commercial gates in Culver City?
Yes. The studio lots along Washington and Jefferson Blvds have their own security protocols, and we work within them. We carry the same commercial-grade documentation habits on residential jobs, so every access control repair includes a photo log and written part record. Call (213) 674-2473 for a written price.
Can you match a keypad or card reader to an existing gate motor?
Most of the time, yes. We service LiftMaster, Linear, Viking, DoorKing, and five other major automation brands, so the access control hardware usually integrates with whatever operator is already on the property. Call (213) 674-2473 and we’ll confirm compatibility before quoting.
Gate Parts & Welding in Culver City
The two most common parts failures on Culver City gates are the hinge welds and the bottom rail. Salt moisture works into the weld joints, and the weight of an 80-year-old wrought iron gate does the rest. Gate Parts & Welding work here often means cutting out the rusted section, welding in matching steel, and dressing the joint so it disappears into the original ironwork. We weld on site whenever possible instead of removing a gate that’s held together only by its lower hinge, and we document every weld with a photo before and after.
Hinge Replacement
Signs you need it
A gate that drags at the latch side, creaks under its own weight, or shows rust weeping from the hinge barrel.
What it costs in Culver City
Residential hinge replacement typically runs $90 to $190 per hinge, installed and greased.
How we do it
We support the gate’s weight, unbolt or cut out the failed hinge, weld in the replacement, and photograph the finished alignment.
Post Replacement
Signs you need it
A post that’s leaning more than a quarter inch, concrete that’s cracked at the base, or a gate that suddenly won’t latch because the post moved.
What it costs in Culver City
Post replacement with new concrete footing typically lands between $560 and $995 per post.
How we do it
We cut out the old post, pour a new footing suited to Culver City’s soil, set the post square, and re-hang the gate the same day.
Custom Welding
Signs you need it
A snapped gate picket, a rusted-through bottom rail, or a gate that needs structural reinforcement after decades of coastal exposure.
What it costs in Culver City
Field welding repairs typically run $160 to $400 per section, depending on how much steel needs replacement.
How we do it
We cut out the failed section, weld in matching steel, grind the joint flat, and prime it for paint the same visit.
Gate Rollers
Signs you need it
A slide gate that shudders on its track, a roller wheel that’s worn flat on one side, or a gate that jumps the rail.
What it costs in Culver City
Roller replacement on a slide gate typically runs $150 to $325 per roller assembly.
How we do it
We support the gate, unbolt the failed roller, install a rust-resistant replacement, and photograph the new assembly in the track.
What Gate Parts & Welding Costs in Culver City
| Item | Typical range in Culver City |
|---|---|
| Hinge replacement | $90 - $190 per hinge |
| Post replacement with footing | $560 - $995 per post |
| Custom field welding | $160 - $400 per section |
| Gate roller replacement | $150 - $325 per roller |
Can you weld a wrought iron gate without removing it from the property?
Most repairs, yes. We support the gate in place and weld on site, which matters when a 1930s gate has original masonry posts we don’t want to disturb. Call (213) 674-2473 and we’ll tell you if yours can stay in place.
Do you replace parts on gates you didn’t install?
Yes. More than half our parts and welding work in Culver City is on gates installed decades before we arrived. We source matching steel and hardware, document what we replaced, and stand behind the work with the 365-Day Done Right Promise. Call (213) 674-2473 for a written price.
Brands We Service in Culver City
We carry parts for Linear, Viking, Ghost Controls, and DoorKing on the truck, and we service eight other major automation brands without steering you toward a replacement. Our brands page lists the full lineup. Most parts we need are in local stock or arrive within two days.
Pricing for Gate Repair in Culver City, CA
| Service | Typical range in Culver City |
|---|---|
| Hinge replacement | $90 - $190 per hinge |
| Post replacement with footing | $560 - $995 per post |
| Custom field welding | $160 - $400 per section |
| Gate roller replacement | $150 - $325 per roller |
| Keypad replacement and programming | $125 - $210 |
| Remote programming and replacement | $75 - $165 per remote |
| Phone entry unit replacement | $460 - $975 |
| Card reader replacement with credentials | $650 - $1,100 |
What pushes price up in Culver City is almost always the corrosion. A hinge replacement that’s straightforward on a dry inland gate becomes a fuller job when the surrounding steel is paper-thin and the post has to be shored up first. That’s exactly why we write the price down before any work begins, so the invoice matches the quote.
Neighborhoods We Serve in Culver City
We dispatch crews across Culver City daily. Typical response is same day for emergency gate failures and within one to two days for scheduled parts and welding work.
- Fox Hills
- Ladera Heights
- Mar Vista
- Village Green
- Sunkist Park
Service Area - Cities Near Culver City
We also serve Venice, CA, Inglewood, CA, Beverly Hills, CA, and Santa Monica, CA. If your gate is on the Culver City border and you’re not sure which city handles your permits, call (213) 674-2473 and we’ll sort it out before any work is scheduled.
Serving Culver City, CA - Our Local Coverage Area
We’re based in the Culver City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Culver City
Same day in most cases. A live person answers the phone 24 hours a day, and our crews are dispatched across Culver City daily with parts for Linear, Viking, Ghost Controls, and DoorKing already on the truck. Call (213) 674-2473 and you’ll speak to a person who can schedule the visit immediately.
Sometimes. Culver City runs its own Community Development department, separate from LADBS, and certain gate replacements, especially those on historic properties like Village Green, require city approval beyond a standard permit pull. We identify which jobs need permitting before work starts and factor the timeline into the written quote. Call (213) 674-2473 for guidance on your specific property.
Yes. Condominium gates in Fox Hills fall under HOA jurisdiction, and we coordinate directly with property managers on access control repairs, slide-gate operator replacements, and parts documentation. The written photo record we leave on every visit is standard practice for HOA compliance. Call (213) 674-2473 and we’ll work within your association’s process.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Culver City Customers Say
"Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.