Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Venice, CA
Gate access control in Venice means working with salt air, morning marine layer, and a housing stock that jumps from 1920s beach cottages to glass-and-steel new builds on the same block. We service keypads, phone entry systems, card readers, and video intercoms on gates that face conditions found nowhere else in Los Angeles, and we price every job in writing before any work begins. Call (213) 674-2473 for someone who can tell you the cost on the phone, not after the fact.
Why Venice Homes Are Different
The Venice Canals off Dell Avenue put hundreds of gates within feet of open water. Salt air from the Pacific hits one side while standing-water humidity rises from the canals on the other. That dual-corrosion environment eats gate hardware measurably faster than even a mile inland. Uncoated steel hinges within a few blocks of the beach can show significant rust inside a single season.
Then there are the walk streets. Roughly a dozen car-free pedestrian paths, including Cabrillo Avenue and Broadway Court, have homes with no driveway access at all. Gate work there means small pedestrian swing gates, often with no power source nearby. A technician who shows up thinking vehicle gate defaults to the wrong job. We dispatch with that in mind.
The housing stock compounds it. Craftsman bungalows from the 1920s through the 1940s sit alongside post-2010 modern builds from the Silicon Beach teardown wave. One block might need century-old wrought iron hinges rebuilt; the next needs a DoorKing control board diagnosed. Venice requires a shop that moves between both without blinking.
Our Main Venice Services
Most Venice calls fall into two buckets: keeping existing gates working, and building or upgrading them to survive this climate. These three pages cover the work in detail.
Gate Repair in Venice
Rusted hinges, sagging posts, broken rollers, snapped cables. On a Venice walk street, a pedestrian gate that will not latch is a security issue, not a nuisance. On a canal-front property, the same repair needs corrosion-resistant hardware or you will be paying for it again in eighteen months. We write the scope, hand you the price, and photograph everything before we leave. That is the standard, and it applies to every Gate Repair in Venice job we take.
Gate Installation in Venice
New gate projects in Venice need to answer one question before the first post hole is dug: what is this gate going to live next to? Canal water, beach air, or a shaded walk street all demand different materials and coatings. We spec accordingly, then build to a written plan. For a full breakdown of how we handle a Gate Installation in Venice, start with that page.
Gate Motor & Opener in Venice
Motors fail faster in Venice than they do inland. The marine layer that blankets the neighborhood from May through August keeps control boards and wiring damp for hours every morning. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the motor already on your property is the one we repair. Details on the Gate Motor & Opener in Venice work we do are on that page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Venice
Gate access control in Venice has to survive what the coast throws at it. The morning marine layer keeps keypad housings and intercom boards damp for hours daily from May through August, and salt in the air shortens the life of exposed wiring and connectors. On the canal side, standing humidity does the same work from below. We spec sealed enclosures and corrosion-resistant connections on every Venice access job, because the alternative is a keypad that works in June and dies in November. This is exactly the work covered on our Gate Access Control hub page, and we bring the same commercial documentation habit to every Venice install.
Keypad Entry
Signs you need it
Keys that require monthly copying, codes that work intermittently when the fog rolls in, or a keypad housing showing white oxidation around the seam.
What it costs in Venice
Keypad entry work in Venice typically runs from $300 to $800 installed, depending on whether we are replacing a weathered keypad or running new low-voltage wire to the control board.
How we do it
We pull the old unit, photograph the wiring before touching anything, install a sealed keypad rated for coastal exposure, reprogram codes, and hand you a written record with the new wiring diagram.
Video Intercom
Signs you need it
A gate with no visual verification, an intercom that crackles when the marine layer sits on the block, or tenants who buzz in visitors sight unseen.
What it costs in Venice
Video intercom systems in Venice generally run $1,200 to $3,000 installed, with the spread driven by whether we are adding a single door station or tying into an existing multi-unit panel.
How we do it
We mount a weather-sealed camera station, run shielded cable where existing wiring is corroded, configure the inside monitors, and leave you with a photo log of every connection point.
What Gate Access Control Costs in Venice
| Item | Typical range in Venice |
|---|---|
| Keypad entry system, installed | $300 - $800 |
| Video intercom, single door station | $1,200 - $2,200 |
| Multi-unit video intercom retrofit | $2,200 - $3,000 |
Can you waterproof a keypad for the Venice marine layer?
Yes. We use sealed, gasketed keypads rated for outdoor coastal exposure and apply dielectric grease to every connector before closing the housing. The marine layer stops being a problem when the enclosure is actually sealed.
Will a video intercom survive canal-front humidity?
It will if it is specced correctly. We choose camera stations with conformal-coated boards and install drip loops on all exterior wiring. Most Venice intercom failures we see are from indoor-rated equipment mounted outdoors, not from the humidity itself.
Gate Parts & Welding in Venice
Gate parts in Venice fail on a schedule the rest of Los Angeles does not share. Hinges rust through, posts rot at the base where canal humidity sits, and gate frames corrode along the bottom rail where morning dew collects. Welding repairs on 1920s wrought iron demand a different hand than structural steel on a 2018 build, and we work both. The full scope of our Gate Parts & Welding capability applies directly to what Venice gates need, and we stock the common components so a repair does not wait on a parts truck.
Hinge Replacement
Signs you need it
A gate that scrapes the ground at the latch side, a visible rust bloom around the hinge pin, or a gate that has dropped more than half an inch since last year.
What it costs in Venice
Hinge replacement in Venice runs $150 to $500 per hinge, depending on the size of the gate and whether the post itself needs reinforcement.
How we do it
We unload the gate onto a temporary support, cut or unbolt the old hinge, grind the mounting surface clean, weld or bolt a corrosion-resistant replacement in place, and photograph the finished weld.
Custom Welding
Signs you need it
A cracked frame member, a broken decorative scroll, or a gate that has pulled away from the post at a weld point after decades of salt exposure.
What it costs in Venice
Custom welding repairs in Venice typically run $200 to $900, with the spread set by the length of the repair and whether we need to fabricate a section to match existing ironwork.
How we do it
We grind the affected area to clean metal, weld the repair, apply a zinc-rich primer and topcoat matched to your gate, and give you before and after photos with the work record.
What Gate Parts & Welding Costs in Venice
| Item | Typical range in Venice |
|---|---|
| Hinge replacement, per hinge | $150 - $500 |
| Post reinforcement and re-set | $400 - $1,000 |
| Custom welding repair | $200 - $900 |
Do you weld wrought iron gates on Venice’s older cottages?
Yes. We match the existing iron profile where we can, weld the repair, and treat the joint so it does not flash rust within weeks. The goal is a repair that does not look like a patch.
Can you replace one hinge or do I need a set?
Usually one hinge can be done. We check the other hinges while the gate is supported, and if one is ready to fail we tell you and price both before any work begins. You make the call from a written price, not a surprise.
Brands We Service in Venice
We work on Viking, Ghost Controls, DoorKing, and Elite systems regularly in Venice, and we service seven major gate-automation brands total: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. The common boards and remotes are stocked locally, which means most motor and access-control repairs in Venice are one visit instead of two. See our brands for the full list.
Pricing for Gate Repair in Venice, CA
| Service | Typical range in Venice |
|---|---|
| Keypad entry system, installed | $300 - $800 |
| Video intercom, single door station | $1,200 - $2,200 |
| Multi-unit video intercom retrofit | $2,200 - $3,000 |
| Hinge replacement, per hinge | $150 - $500 |
| Post reinforcement and re-set | $400 - $1,000 |
| Custom welding repair | $200 - $900 |
Two things push Venice prices above inland rates: the corrosion-resistant hardware this climate requires, and the extra time to properly prep and coat surfaces that sit in salt air. The written price you receive before work starts is the price you pay, no exceptions and no surprise invoice at the end.
Neighborhoods We Serve in Venice
We work throughout Venice, from the canal-front homes near Dell Avenue to the walk streets of Cabrillo Avenue and Broadway Court, and across the modern builds that line the Silicon Beach corridor. Most Venice calls get a same-day or next-day visit depending on the schedule, and we confirm the time window before dispatch.
- Venice Canals
- Silver Triangle
- Oakwood
- Windward Circle
- Venice Walk Streets
Service Area - Cities Near Venice
Our Venice crews also cover the surrounding Westside. If you are in Santa Monica, CA, Culver City, CA, Beverly Hills, CA, or Inglewood, CA, the same written-price standard and documented photo record apply on every gate job.
Serving Venice, CA - Our Local Coverage Area
We’re based in the Venice area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Venice
Same day in most Venice neighborhoods. A live person answers the phone 24 hours a day, seven days a week, and we dispatch local crews with the parts already on the truck for common failures. We tell you the time window before anyone leaves the shop.
Most repairs do not need a permit in Los Angeles, but new automatic gate installations and some structural post replacements may require one depending on the scope and the property’s zoning. We can tell you whether your job needs a permit after we see the gate and the existing setup.
Yes. Many walk-street homes in Venice have pedestrian gates with no power source, and we have installed solar-powered and battery-backed access systems for those properties. We can tell you what your options are after a quick site visit, and the written price covers the full install.
If your gate needs work in Venice, call (213) 674-2473 for a free estimate and a written price before any work begins. A live person answers, and we will tell you what the job costs before we send a technician to your gate.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Venice Customers Say
"Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.